VWVORTEX LAUNCHCONTROL WINDOWS

The vehicle must be under panic stopping conditions before the lighting activates as shown here.īyte 18 - Do Not alter this if you are not retrofitting rear lights ! Note: MY 2011 owners may want to see: Change comfort turn signals count in the VW VortexĮmergency Brake Warning via turn signals and/or via brake lights active Coding or MFA / dash options may apply to this setting in some cases.From the drop down list, choose the number of flashes and Save. Automatic Front and /or Rear Fog Light dimming (shutting OFF) may be required by law, altering these settings is NOT recommended.Depending on equipment level, two separate coding bits should be available.This seems to control the fogs as cornering lights with turn signal.įront and /or Rear Fog Light dimming behavior with High Beams Also see Byte 17, Adaptive Light/Cornering Light Variant.The headlights must be turned on and the turn signal must be on in the turning direction.The headlights must be turned on and the steering wheel must be in the turning direction.Notes: After 'Cornering Lights via Front Fog Lights active' is enabled, the lights may work under the following conditions: bmw511 and several of the other forum members have Audi A3 contributions in that forum as well.Ĭornering Lights via Front Fog Lights active This appears to be sorted per the post from Tim S.LED DRL Dimming in Parking light switch position for Xenon equipped vehicles with factory LED DRLs Disable 'Daytime Running Light (DRL) only active with Assistance Driving Light (ADL) active'.Note: Depending on the Byte 18 coding, this may result in all of the parking lights illuminating.ĭaytime Running Lights enabled with OFF and Auto switch positions - common when importing vehicles from the US -to- Canada Disable Factory DRL's in Byte 15 - un-check 'Daytime Running Lights (via separate lights) active'.Byte 14 - Check 'Daytime Running Lights (DRL) via Fog Lights active'įogs and Xenon Headlights as DRLs (Both) for Xenon equipped vehicles or Halogen equipped using the main low/dipped beamįogs as Daytime Running Lights for Halogen equipped vehicles or using a separate bulb or filament for DRL only.Byte 11 - Un-check 'Daytime Running Lights (via Low Beam) active'.Note: If installed modules support this activation you can turn the DRLs on or off via the MFA providing DRLs were not disabled via coding.įogs as Daytime Running Lights for Xenon equipped vehicles or Halogen equipped using the main low/dipped beam Daytime Running Light (DRL) Adaptation active (MFA+).Factory Halogen (generally when using a separate bulb or filament for DRL only) – Byte 15 (DRL)ĭaytime Running Lights on/off via MFA - supported on most 2011+ m.y.Factory Xenon (or Halogen DRL's that are using the main low/dipped beam) – Byte 11 (PRL).

VWVORTEX LAUNCHCONTROL WINDOWS

Example: Permanent Running Light (PRL) via Low Beam activeĬlose the Long Coding Helper by clicking the Windows X box on the top right of the screen or clicking the Exit button on the top left of the screen to send your altered Coding value back to the Coding screen.ĭaytime Running Lights - The lamp systems are different: Check or Un-check the boxes for the desired results. Or the module you intend on tweaking as per the list belowĬlick on each of the Byte numbers in row 3) and you'll see the selectable options below. Click on each of the Bytes and Bits for the documented options and check or un-check the appropriate boxes as shown in the example below: LightingĪll modifications are found in Found in > Long Coding Helper unless otherwise noted. Note: Make sure to have all Doors unlocked, otherwise this Control Module may not communicate with the Scan Tool / VCDS. Central Electronics / Body Control Module (BCM)

This may not be supported on all control modules.

From the drop down list, choose Storage of seat heater level driver. 1, 2 or 3) should resume the previous level upon restarting the car.

Enable Indirect TPMS using the documented Long Coding Helper information and the forum feedback here: How to: retrofit indirect Tire Pressure Monitoring in 5 minutes.

Alter the HHA (Hill Hold Assist) using the documented Channel while connected to the vehicle.

On Vehicles using the MK60EC1 ABS system it may be possible to: 3 - Central Electronics / Body Control Module (BCM).

Vwvortex launchcontrol